PolarFIS Installation on VW Golf 6 (UK)

From AutoPolar
Jump to: navigation, search

Beginning[edit]

First of all, thanks for buying PolarFIS, throughout this manual we are going to explain how to install your new PolarFIS.

To install PolarFIS, you will need the following tools:

  • Blade screwdriver
  • Torx Wrench T30
  • Plastic bridles to hold PolarFIS device

After this, check that your PolarFIS unit have the last firmware version available for your vehicle, or not will appear nothing in your FIS display. There are different firmwares for different platforms and display, so it is very important have the correct one. For upgrade your device to the last version, go to the official website AutoPolar and download the UpdaterTool software. You will find a direct link at the upper position of this website.

IMPORTANT : Because during the PolarFIS installation some elements of the vehicle, like the lighting system control and the Gateway must be disconnected, it is advised to disconnect the battery before coming to the installation.


Disassembling[edit]

For the installation of your PolarFIS, we leave here some indicatives photos.
For start, we will have to open bonnet and remove foam pads at either side of the scuttle panel. (see the images below)


Golf6rhd1.jpg
Golf6rhd2.jpg


Unclip the wire on the drivers side of the scuttle panel. its pretty tight but it will come off.


Golf6rhd3.jpg


Now use small flat head to remove the two caps on the wiper nuts, Once these caps are off, remove the two nuts and store to one side.
Press on the hige of the wipers as shown in pics. Once you feel them coming loose start to lift the wiper up at the blade end and it should pop off.


Golf6rhd12.jpg


Put hander under plastic scuttle cover and pop it up as shown in the pics. again this is a bit stiff but it'll pop off no problem. beware of paintwork when you take the plastic cover away.


Golf6rhd5.jpg
Golf6rhd6.jpg


Using small screwdriver remove the plug on the wiper motor


Golf6rhd7.jpg


Now, remove the metal "tray" in front of the wiper motor 1x10mm nut, 1x10mm bolt.
Once removing the two holding down bolts the plate will pull up and be out of the way.
Using the T30 Torx bit, remove the two torx screws holding the wiper motor on.


Golf6rhd8.jpg
Golf6rhd9.jpg


Wiggle the wiper motor free and put to one side.
Remove the 3x10mm nuts holding on the plastic cover in the pic. Once these are removed, you will see the Gateway.


Golf6rhd10.jpg
Golf6rhd11.jpg


Connecting your PolarFIS[edit]

IMPORTANT : Before coming to connect PolarFIS, it is advised to disconnect the battery of the vehicle or in lack of that, to remove the contact of the vehicle since the Gateway is the central unit that interconnects all the electronic modules of the vehicle.

Now we must connect the Gateway connection to PolarFIS, and after then, PolarFIS to the Gateway of the car, therefore to make a “bridge”. After this, you will have already connected your PolarFIS, now you will have to fix it with the aid of plastic bridles.

IMPORTANT : Make sure that the connectors are perfectly fitted, once you have connected your PolarFIS.


Finishing installation[edit]

Before returning to place the equipped ones, connect the vehicle battery and put the contact in order to verify that you have a new menu called PolarFIS within FIS screen of your vehicle. If you are not able to accede to this screen, it is probably that there is a loose or wrong place connector, you should verify again that everything is correctly connected. Once you have made this verification, remove the contact of the vehicle and comes to mount all the disassembled pieces again, following the same steps but the other way round.

IMPORTANT : You should take into account that after disconnecting the battery of your vehicle, perhaps the memory of some accessories is loosened, as for example the windows or the limits of the power-assisted steering. 


In the case of the windows, you will have to put each window down until the end, and later you must put it up again so that the ECU of the door memorise all the possible positions. This process must be done in each window of the vehicle.

In the case of the power-assisted steering, if failure lights are on, you may do the following: With the car stopped, slowly turn the steering wheel until the left limit and keep it only few seconds. Secondly, turn it again until the right limit and keep it because later you have to turn again the steering wheel until its central position. Finally, drive some meters with the steering wheel totally straight and the failure lights of power-assisted steering will disappear. Now you can erase the errors with the VAGCOM and the process will end.


From that moment on, the process of PolarFIS installation will have finished, if you have any doubt or problem during the installation, don not hesitate to consult us about your problem.
You can access our tickets systems here and your doubt will be solved as soon as possible.


Videos[edit]